$440.00

 #GCT171220

AMD high speed, series motor. 36-volt (4-hp@4400 rpm) with 19 spline coupler. For Columbia and Melex with Dana axle, E-Z-GO 1988-up series cars, Yamaha G14, G16. Speeds up to 20 mph with stock controller. Also works on 48-volt. Not for use on PDS or DCS cars.

$399.00

EZGO Series Motor 19 Splined Axles/Speeds Up to 19 MPH/8.0 Peak Horsepower.
Can be used with OEM controllers Add a 400 AMP controller or larger for increased speed & torque. Gain up to 8 MPH additional speed with a 5-10% loss of torque.

D-31, HT-D297, ADC 6-224C
 

$424.00

#GCT1032640
 

AMD series motor. 36-volt (2-hp@2800 rpm). 19 spline coupler. Not for use on PDS or DCS cars. Also fits Columbia ParCar, Melex, Yamaha electric G9 (1992½-95) G14,G16.

$515.00

#GCT1071240

AMD 36-volt (8-hp@1600 rpm), 48-volt (11.4-hp@2300 rpm) high torque motor with 19 spline coupler for E-Z-GO 1988-up series cars. For maximum performance, safety, and durability, 4 gauge cables (#GCT101248) throughout the car, heavy duty solenoid and F&R switch are required. Minimum 400 amp controller required. Not for use on DCS or PDS cars.

$556.00

#GCT1071260

AMD 36-volt (6.1-hp@5330 rpm) HIGH SPEED series motor with 19 spline coupler for E-Z-GO 1988-up series cars. Works great on 48-volts! For maximum performance, safety, and durability, 4 gauge cables (#1248) throughout the car, heavy duty solenoid and F&R switch are required. Minimum 400 amp controller required.. Not for use on DCS or PDS cars.

$419.00

#GCTMOTB2

EZGO PDS & DCS 19 Splined Axles/ Speeds Up to 21 MPH/8.4 Peak Horsepower.
Can be used with OEM controllers, Add a 400 AMP controller or larger for increased speed & torque. Gain up to 8 MPH additional speed with a 5-10% loss of torque

 6-224H, XP-2140
 

$598.00

High speed, series 36-volt (6.1hp@5330rpm) Controller upgrade suggested to at least 400 amp, also 4 gauge cables and high amp for F&R set up.

$449.00

36-volt (8-hp@1600 rpm) 48-volt (11.4-hp@2300 rpm) HIGH TORQUE motor with 19 spline coupler for E-Z-GO 1988-up series cars. Add a 400 AMP controller or larger for increased speed & torque.

$575.00

Industrial speed series 48-volt (4hp@4400rpm) Uses high stock or aftermarket controller. For E-Z-GO 1988-up series

$626.00

#GCT1032680

EZGO DCS or PDS  High Torque Motor 400 Amp controller recommended. For more speed add a 500 or 600 amp controller with this. 8.5hp, 36-volt

If using factory controller you need cable adapter #GCT103228  $35.00

$499.00

#GCT1032670

AMD 36-volt (4.45-hp@3570 rpm) motor. The speed sensor plug on this motor does not match the E-Z-GO PDS motor. Use cable # GCT103228 with OEM and GE controllers. #GCT103228 is not needed with Alltrax controllers. For E-Z-GO PDS/DCS. Can also be used on 48-volt.

$429.00

AMD, EZGO PDS/DCS 36V, 2.25HP; 2565 RPM Stock Motor.  73445GO2, 73124GO1

$2599.00

EZGO AC Conversion Kit

GCTEZACMOTOR

* POWERFUL high torque and fast hill climbing capabilities
* Digital Display
* REGENERATIVE BRAKING puts power back into the batteries
* 48 VOLT SYSTEM
* GOLF MODE where top speed is 16 MPH, acceleration and regenerative braking are reduced while powerful hill climbing torque is retained
* STREET MODE where top speed is increased to 25 MPH with greater acceleration and full regenerative braking power
* CONSERVATION MODE for a low battery condition where energy conservation is key. Speed and acceleration are reduced while full regenerative braking is retained. In this mode you will still be able to achieve speeds up to 15 MPH